High Power Module
(Dual-band 802.11abgn Wi-Fi module with high output power)

The RS9113 High Power Module is based on Redpine Signals' RS9113 ultra-low-power, single spatial stream, dual-band 802.11n + BT4.0 + ZigBee Convergence SoC. The RS9113 module integrates a multi-threaded MAC processor with integrated analog peripherals and support for digital peripherals, baseband digital signal processor, analog front-end, crystal oscillator, calibration OTP memory, dualband RF transceiver, dual-band high-power amplifiers, baluns, diplexers, External PA, diversity switch and Quad-SPI Flash thus providing a fully-integrated solution for embedded wireless applications. The RS9113 based chips and modules leverage and improve upon Redpine’s proven low power innovations from Lite-Fi™ products (RS9110) and provide WLAN 802.11n, BT4.0 and ZigBee convergence solution for integration into mobile and M2M communication devices. It can connect to a host processor through SDIO, USB, SPI or UART interfaces.


Part Number


System diagram

Features and Benefits

  • Ultra-low-power, low-cost and high-throughput 1 Tx – 1 Rx Dual-band 802.11n + BT4.0 (dual-mode) + Zigbee (802.15.4-2009)
  • Supports 20MHz and 40MHz bandwidth
  • Data rates up to 150 Mbps using 1-Spatial Stream 802.11n
  • WLAN Tx output power up to +23dBm in 2.4GHz and +20dBm in 5GHz
  • WLAN Receiver with -97dBm in 2.4GHz and -94dBm in 5GHz Rx sensitivity
  • High performance Bluetooth receiver with -94dBm Rx sensitivity
  • Support for Bluetooth Transmit power class-1
  • High performance ZigBee receiver with -102dBm Rx sensitivity
  • Support for multiple ZigBee output powers up to +20dBm
  • Innovative coexistence algorithms for optimum throughput of Wi-Fi and collocated Bluetooth and ZigBee modems
  • Integrated Ultra-low-power subsystem with <3uA watch-dog mode and <30uA standby mode.
  • Hardware Assisted Radar-detection for compliance to FCC and ETSI norms, enabling usage of more channels in the 5GHz band.
  • Complete software along with host driver for various operating systems such as Windows, Linux, Windows CE, and Android.
  • PA Power supply 5v to 3.3v (reduced TX power).
  • Support for multiple host interfaces to allow maximum flexibility for the system integrator. Host interfaces supported are USB 2.0, SDIO, SPI and UART

Wireless Specifications

  • IEEE 802.11a/b/g/n, 802.11j, 802.11n, 802.11d/e/i, 802.11w 802.1X, 802.11k,,802.11v, 802.11r, 802.11h
    Bluetooth v2.1 EDR, v4.0
    802.15.4-2009 (2.4GHz)
  • 802.11n: from 6.5 Mbps to 150 Mbps (MCS 0-7)
    802.11a/g: from 6 Mbps to 54 Mbps
    802.11b: from 1 Mbps to 11 Mbps
    Bluetooth: 1, 2, 3Mbps
    802.15.4-2009: 250Kbps
  • OFDM with BPSK, QPSK, 16-QAM and 64-QAM
    802.11b with CCK and DSSS
    Bluetooth: GFSK, DQPSK, 8DPSK
    802.15.4-2009: DSSS
  • 1-SS, 40MHz bandwidth, Greenfield Preamble, Short-GI, 1 spatial stream STBC, RIFS, A-MSDU, A-MPDU, Aggregation with Block-ack, A-MSDU inside A-MPDU and Virtual AP support
  • Scatternet, Adaptive Frequency Hopping, Interlaced scanning, 15 active slaves in proprietary mode, hold, sniff and park modes
  • CCM* security, orphan scanning, coordinator realignment
  • Wi-Fi client, Access point, Wi-Fi Direct
  • Master, slave, scatternet
  • ZigBee Coordinator, Router, End device
  • WMM and WMM Power Save Support
  • USB 2.0, SPI, UART, SDIO
  • I2C, I2S, SPI, QSPI, USART, GPIO, JTAG, Analog(ADC/DAC) and Ultra-low-power peripherals.
  • 3.0-3.6V, 1.8-3.6V , 3.3 - 5V for PA
  • Industrial Grade -40ºC to +85ºC
  • WiFi Alliance (802.11abgn, WPA, WPA2 Personal and Enterprise, WMM, WMM-PS, WPS, Wi-Fi Direct™, Voice-Personalß, Protected management frames),
    Cisco CCX v5,
    Bluetooth-SIG Qualification,
    World-WideRegulatory Compliance:
    FCC(IDs are XF6-RS9113SB, XF6-RS913DB)
    IC(IDs are 8407A-RS9113SB, 8407A-RS9113DB),
  • Wi-Fi: 23 dBm for 802.11b DSSS in 2.4GHz and 20 dBm in 5GHz
    23 dBm for 802.11g/n OFDM
    20 dBm for 802.11a/g/n OFDM
    Bluetooth: 20 dBm
    ZigBee: 20 dBm
  • Wi-Fi: 1 Mbps -97 dBm (< 8% PER)
    6 Mbps -94 dBm (<10% PER)
    54 Mbps -76.5 dBm (< 10% PER)
    MCS7 (20MHz) -73 dBm (< 10% PER)
    MCS7 (40MHz) -69.5 dBm (< 10% PER)
    Bluetooth: 1 Mbps -94 dBm
    2 Mbps -92 dBm
    3 Mbps -84 dBm
    BTLE (1Mbps) -91 dBm
    ZigBee: 250 Kbps -102 dBm (< 8% PER)
  • : These features are not supported by current software releases. Contact Redpine Signals sales (sales@redpinesignals.com) for details.
  • : These certifications are in progress at this time. Contact Redpine Signals Sales (sales@redpinesignals.com) for more details and for certifications not listed here.
  • ß: Applicable to n-Link® modules only
  • Note : Regulatory certifications to be done.Tx/Rx Power numbers may change after Certification.

Device Listing

Device Number Description Packaging Qualification
RS9113-NBZ-H0X Dual band HPM module with no antenna and integrated Wi-Fi, Bluetooth and ZigBee. Tray Industrial

Device Ordering Information

The device numbering is based on the following naming convention. All the devices are labeled as RS9113-NBZ-H0X Where

Evaluation Package

The evaluation package comprises RS9113 HPM module based evaluation board. This is accompanied by firmware, reference drivers for Linux, Windows and Android operating systems with documentation.

Module Reference Design

Redpine offers form-factor SPI, USB2.0, UART and SDIO reference designs along with software for manufacture testing and diagnostics. For details on availability please contact sales