RS10002 WiSeMCU Module Family


Redpine Signals RS10002 WiSeMCU device is the industry's first Wireless MCU with a multi-protocol wireless (Wi-Fi+Bluetooth+Zigbee) sub-system. It is a fully integrated module with an ultra-low-power ARM Cortex M4F microcontroller as an application processor, a built-in wireless subsystem, advanced security, power-management, frequency reference, RF power-amplifiers, diversity RF Front-end and passives. The WiSeMCU™ comes with an SDK to enable plug-and-play hardware and software development for the wireless Internet of things. The ultra-low-power microcontroller subsystem in RS10002 integrates an ARM Cortex M4F processor with 104 KB of on-chip SRAM and 512KB of on-chip flash available for application development. A slew of peripherals including, multiple USARTs, SPIs, I2Cs and I2S-bus interfaces, comprehensive timers and 12-bit ADC satisfy the interfacing needs of most IoT devices. The comprehensive wireless networking subsystem in RS10002 integrates 1x1 802.11n, advanced TCP/IP networking stack, Bluetooth4.0 solution with integrated application profiles and ZigBee for Home Automation and Smart Energy applications.

Features and Benefits

  • Application subsystem with Cortex M4+Cortex M0 running at 100MHz up to 512KByte Flash Memory and 104KB SRAM.
  • Wireless subsystem with support for multi-protocol wireless Wi-Fi+ BT EDR 2.1 + BT LE + Zigbee.
  • Support for USART, SPI, I2C, I2S, USB, ADC, Timers, Interrupts, PWM, GPIOs.
  • Embedded WLAN stack, TCP/IP stack, Bluetooth Stack, ZigBee Pro Stack embedded in the device.
  • SDK to enable hardware and software development.
  • Fully certified FCC/CE/IC module
  • Advanced low-power modes with deep power mode <100n

Module Footprint and Dimensions

RS10000 module
14mm X 15mm


  • Home Automation - Displays/Thermostats
  • Home Appliances – Smart Meters
  • Security Systems – IP Network Sensor Nodes
  • Wi-Fi- BT Gateway, WiFi-ZB Gateway
  • Portable fitness & health monitoring
  • Fleet management and asset tracking
  • Wireless Headsets and speakers
  • Medical Devices
  • Gaming Consoles
  • Intelligent Sensing
  • Wearables
  • Industrial monitoring and control
  • Other M2M applications


  • IEEE 802.11 b/g/j, 802.11n, 802.11d/e/i/w, 802.1X, 802.11k/r/v, Bluetooth v2.1 EDR, v3.0 + HS, v4.0 802.15.4-2006 (2.4GHz).
  • 802.11n: from 6.5 Mbps to 150 Mbps (MCS 0-7) 802.11b: from 1 Mbps to 11 Mbps Bluetooth: 1, 2, 3Mbps 802.15.4-2006: 250Kbps
  • OFDM with BPSK, QPSK, 16-QAM, 64-QAM and 256-QAM 802.11b with CCK and DSSS Bluetooth: GFSK, DQPSK, 8DPSK 802.15.4-2006: DSSS
  • WMM and WMM Power Save Support
  • 802.11n:
    1-SS, 40MHz bandwidth, Greenfield Preamble, Short-GI, 1 spatial stream STBC, RIFS, A-MSDU, A-MPDU, Aggregation with Block-ack, A-MSDU inside A-MPDU, PSMP, MTBA, Fragmentation and Virtual AP support
  • Scatternet, Adaptive Frequency Hopping, Interlaced scanning, 15 active slaves in proprietary mode, hold, sniff and park modes
  • CCM* security, orphan scanning, coordinator realignment, mesh routing
  • Embedded Wi-Fi client, Access point, Wi-Fi Direct
  • Master, slave, scatternet
  • ZigBee Coordinator, Router, End device
  • TCP, UDP, DHCP, ARP, IGMP, DNS client. Integrated web server, ZigBee and BT Stack.
  • I2C, I2S, SPI, USART, GPIO, JTAG, Analog(ADC) and Ultra-low-power peripherals, Timers, SCT-Timer/PWM,RTC, MRT, WWDT, POR, BOD, RC OSC,WD OSC,32kHz RTC, PLL.
  • 3.0-3.6V, 2.2-3.6V
  • Industrial Grade -40ºC to +85ºC
  • Wi-Fi: 18 dBm for 802.11b CCK 18 dBm for 802.11g/n OFDM Bluetooth: 15dBm ZigBee: 15dBm.
  • Wi-Fi: 1 Mbps -97 dBm 54 Mbps -75 dBm MCS7: -72 dBm Bluetooth: -94 dBm ZigBee: 250 Kbps -102 dBm
  • WiFi Alliance (802.11bgn, WPA, WPA2 Personal and Enterprise,WMM-PS, WPS, Wi-Fi Direct™, Voice-Personal, Protected management frames), Cisco CCX v5, Zigbee Certification Bluetooth Qualification, FIPS 140-2, World-Wide Regulatory Compliance (FCC, IC, CE, ETSI, TELEC)
  • : These features are not supported by current software releases. Contact Redpine Signals sales ( for details.

Evaluation Package

The evaluation package comprises WiSeMCU module based board, accompanied by SDK and source code for peripheral interfaces, API library and hardware and software documentation. For details on availability please contact sales.